Maximum Power Point Tracking Dual Axis Solar Panel Using Arduino UNO
Keywords:
Power Supply, ArdunioUnio; Servo Motor, Solar Panel, LDR, Embedded C, Module Solar Panel, 5v Charger; Ardunio Ide.
Abstract
Renewable energy is the only way to reduce global energy shortages. Solar is a high-yield renewable resource. Solar energy is becoming a major renewable energy source. Modern technologies include solar heating, photovoltaic, solar thermal energy, solar architecture, molten salt power plants, and artificial photosynthesis utilise solar light and heat. We represented the Dual Axis Solar panel with a 10W, 21V, 0.57 solar panel. We built a solar panel framework. Crafting the framework using cardboard cuts project costs. Trackers point solar panels at the sun. These devices rotate to follow the sun to maximum energy capture. Solar trackers can boost electricity generation by a third or even 40% in some countries compared to fixed-angle modules. When modules are constantly adjusted to the optimal angle as the sun moves, solar conversion efficiency improves. This paper designs an Arduino UNO-based Dual Axis Solar Tracking system to move solar panels toward maximum sunlight. The fixed solar system could maximise solar panel production by improving efficiency. LDRs send a signal to the Arduino UNO, which sends it to the servo motor connected to it, which positions the Axis Solar Panel in the sun's direction. This allowed Arduino UNO to track dual-axis solar panels with maximum power. Our technology is more efficient, small, low-cost, and easy to use.
Downloads
Download data is not yet available.
References
A. Mohamad, H. Mhamdi, N. A. M. Amin, M. Izham, N. A. Aziz, and S. Y. Chionh, “A review of automatic solar tracking systems,” J. Phys. Conf. Ser., vol. 2051, no. 1, p. 012010, 2021.
T. Kaur, S. Mahajan, S. Verma, Priyanka and J. Gambhir, “Arduino based low cost active dual axis solar tracker,” 2016 IEEE 1st International Conference on Power Electronics, Intelligent Control and Energy Systems (ICPEICES), Delhi, India, 2016, pp. 1-5.
M. H. M. Sidek, N. Azis, W. Z. W. Hasan, M. Z. A. Ab Kadir, S. Shafie, and M. A. M. Radzi, “Automated positioning dual-axis solar tracking system with precision elevation and azimuth angle control,” Energy (Oxf.), vol. 124, pp. 160–170, 2017.
Q. Ha and M. D. Phung, “IoT‐enabled dependable control for solar energy harvesting in smart buildings,” IET Smart Cities, vol. 1, no. 2, pp. 61–70, 2019.
S. M. Fatemi, M. S. Shadlu and A. Talebkhah, “A New Method for Maximum Power Point Tracking in Solar PV Systems by Combining Extremum Seeking Method (ESM) and Model Predictive Control (MPC),” 2020 11th Power Electronics, Drive Systems, and Technologies Conference (PEDSTC), Tehran, Iran, 2020, pp. 1-5.
R. Medhane, S. Dhamal, and M. Thakre, “Solar photovoltaic water pumping system with reduced sensors and IMD using the P&O MPPT algorithm,” SSRN Electron. J., 2021.
M. Qenawy, W. Zhou, and Y. Liu, “Effects of crossflow-fed-shaped holes on the adiabatic film cooling effectiveness,” International Journal of Thermal Sciences, vol. 177, p. 107578, Jul. 2022.
M. Qenawy, W. Zhou, D. Peng, and Y. Liu, “Investigation of Film Cooling Vortical Structures Behind a Cylindrical Hole Fed by an Internal Crossflow,” Sep. 2019.
M. Qenawy, M. Taha, and A. H. Abdelbaky Elbatran, “Unsteady adiabatic film cooling effectiveness behind shaped holes,” Case Studies in Thermal Engineering, vol. 34, p. 102005, Jun. 2022.
M. Qenawy, A. Hamed, W. Abdelfadeel, and S. Abdelhady, “Assessment of the Planned Expansion of Renewable Energy in Egypt,” International Journal of Applied Energy Systems, vol. 0, no. 0, pp. 0–0, Apr. 2022.
M. Qenawy, Y. Chen, J. Wang, J. Tian, and B. Chen, “Intermittent cryogen spray cooling coupled with cold air jet for heat transfer enhancement and cryogen saving of laser dermatology,” Physics of Fluids, vol. 36, no. 2, Feb. 2024.
M. Qenawy, J. Wang, J. Tian, B. Li, and B. Chen, “Investigation of unsteady flow behavior of cryogen-spray coupled with cold air jet,” Appl Therm Eng, vol. 235, Nov. 2023.
M. Qenawy, M. Taha, J. Wang, and A. H. Abdelbaky Elbatran, “Effects of hole-inlet velocity on the adiabatic film cooling effectiveness behind crossflow-fed shaped holes,” Appl Therm Eng, vol. 222, Mar. 2023.
M. Qenawy, W. Zhou, H. Chen, H. Shao, D. Peng, and Y. Liu, “Unsteady Analysis of Adiabatic Film Cooling Effectiveness Behind a Row of Circular Holes Fed by Internal Crossflow,” in Volume 5B: Heat Transfer, American Society of Mechanical Engineers, Jun. 2019.
M. Qenawy, Y. Chen, J. Wang, J. Tian, B. Li, and B. Chen, “Transient behavior of liquid film deposition and surface heat transfer upon cryogen-spray cooling coupled with cold air jet,” Int J Heat Mass Transf, vol. 223, p. 125224, May 2024.
W. Zhou, M. Qenawy, H. Shao, D. Peng, X. Wen, and Y. Liu, “Turbine vane endwall film cooling with barchan-dune shaped ramp in a single-passage transonic wind tunnel,” Int J Heat Mass Transf, vol. 162, Dec. 2020.
W. Zhou, H. Shao, M. Qenawy, D. Peng, H. Hu, and Y. Liu, “Improved Turbine Vane Endwall Film Cooling by Using Sand-Dune-Inspired Design,” Journal of Thermal Science, vol. 31, no. 3, pp. 958–973, May 2022.
J. Tian et al., “Unstable spray pattern and cooling performance of cryogen spray coupled with cold air jet: An experimental study,” Physics of Fluids, vol. 35, no. 12, Dec. 2023.
H. S. El-Mesery, M. Qenawy, Z. Hu, and W. G. Alshaer, “Evaluation of infrared drying for okra: Mathematical modelling, moisture diffusivity, energy activity and quality attributes,” Case Studies in Thermal Engineering, vol. 50, p. 103451, Oct. 2023.
M. Qenawy et al., “Performance and emission of extracted biodiesel from mixed Jatropha-Castor seeds,” Fuel, vol. 357, p. 130060, Feb. 2024.
M. Qenawy, Y. Liu, and W. Zhou, “On the unsteady behaviours of the adiabatic endwall film cooling effectiveness,” IOP Conf Ser Mater Sci Eng, vol. 1172, no. 1, p. 012031, Aug. 2021.
M. Qenawy and S. Abdelhady, “Analytical Study of a Modified Thermal Energy Storage System for PS10 in Aswan,” in The International Conference on Mathematics and Engineering Physics, May 2014, pp. 1–5.
Mohamed Qenawy, “Matlab Simulation of 10 MW Molten Salt Solar Power Tower Plant in Aswan,” Noble International Journal of Scientific Research, vol. 1, no. 1, pp. 34–43, 2017.
Mohamed Qenawy, S. Abdelhady, W. Abdelfadeel, and M. Shaban, “Analytical Study of a Modified PS10 in Aswan,” Int J Sci Eng Res, vol. 5, no. 9, pp. 976–983, 2014.
H. Chen, W. Zhou, M. Qenawy, and Y. Liu, “Experimental Study on Spatio-Temporal Variation of Double-Row Holes Film Cooling Effectiveness with Oscillating Mainstream,” Sep. 2019.
W. Zhou, M. Qenawy, Y. Liu, X. Wen, and D. Peng, “Influence of mainstream flow oscillations on spatio-temporal variation of adiabatic film cooling effectiveness,” Int J Heat Mass Transf, vol. 129, pp. 569–579, Feb. 2019.
M. Qenawy, L. Yuan, Y. Liu, D. Peng, X. Wen, and W. Zhou, “A Novel Single-Passage Transonic Wind Tunnel for Turbine-Vane Film Cooling,” J Eng Gas Turbine Power, vol. 142, no. 7, Jul. 2020.
M. Qenawy, H. Chen, D. Peng, Y. Liu, and W. Zhou, “Flow Structures and Unsteady Behaviors of Film Cooling from Discrete Holes Fed by Internal Crossflow,” J Turbomach, vol. 142, no. 4, Apr. 2020.
M. Qenawy, W. Zhou, and Y. Liu, “Effects of crossflow-fed-shaped holes on the adiabatic film cooling effectiveness,” International Journal of Thermal Sciences, vol. 177, p. 107578, Jul. 2022.
Ananda Shankar Hati, and T. K. Chatterjee, "Symmetrical component filter based online condition monitoring instrumentation system for mine winder motor" Measurement (Elsevier), vol. 82, pp. 284-300, 2016.
Prashant Kumar and Ananda Shankar Hati "Review on Machine Learning Algorithm Based Fault Detection in Induction Motors," Archives of Computational Methods in Engineering, vol: 28, pp: 1929-1940, 2021.
Kumar Prashant and Hati, Ananda Shankar "Convolutional Neural Network with batch normalization for fault detection in SCIM," IET Electric Power Application, vol: 15, issue: 1, pp. 39-50, 2021.
Kumar Prashant and Hati, Ananda Shankar "Deep Convolutional Neural Network based on adaptive gradient optimizer for fault detection in SCIM," ISA Transactions, vol: 111, pp: 350-359, 2021.
Prince, Hati Ananda Shankar, Chakrabarti Prasun, Abawajy Jemal Hussein and Ng Wee Keong "Development of Energy Efficient Drive for Ventilation System using Recurrent Neural Network," Neural Computing and Applications, Vol. 33, no. 14, pp. 8659-8668, 2021.
Sinha Ashish Kumar, Hati Ananda Shankar, Benbouzid Mohamed and Chakrabarti Prasun "ANN-based Pattern Recognition for Induction Motor Broken Rotor Bar Monitoring under Supply Frequency Regulation" Machines (2021), vol: 9(5).
Prince and Hati Ananda Shankar "A Comprehensive Review of Energy-Efficiency of Ventilation System using Artificial Intelligence" Renewable and Sustainable Energy Reviews (2021), vol: 146, 2021.
Kumar Prashant and Hati, Ananda Shankar "Transfer Learning Based Deep CNN Model for Multiple Faults Detection in SCIM" Neural Computing and Applications (2021).
Prince and Hati Ananda Shankar "Temperature and Humidity Dependent MRAS Based Speed Estimation Technique for Induction Motor used in Mine Ventilation Drive" Journal of Mining Science, 2021, Vol. 57, No. 5, pp. 842–851.
Kumar Prashant and Hati, Ananda Shankar "Dilated Convolutional Neural Network Based Model For Bearing Faults and Broken Rotor Bar Detection in Squirrel Cage Induction Motors" Expert Systems With Applications (2022).
Prince and Hati Ananda Shankar "Convolutional Neural Network-Long Short Term Memory Optimization for Accurate Prediction of Airflow in a Ventilation System" Expert Systems with Applications (2022).
Vatsa Aniket and Hati Ananda Shankar "Depolarization Current Prediction of Transformers OPI System Affected From Detrapped Charge Using LSTM," in IEEE Transactions on Instrumentation and Measurement, vol. 71, pp. 1-11, 2022, Art no. 2511711.
Gorai Rahul, Hati Ananda Shankar, and Maity Tanmoy, "A new cascaded multilevel converter topology with a reduced number of components" 3rd IEEE 2017 Conference on International conference on Power, Control, Signals and Instrumentation Engineering (ICPCSI-2017), 21-22 September 2017 | IEEE, Chennai, India., pp. 539-543.
Kumar Prashant, Hati, Ananda Shankar, Sanjeevikumar Padmanaban, Leonowicz Zbigniew and Prasun Chakrabarti "Amalgamation of Transfer Learning and Deep Convolutional Neural Network for Multiple Fault Detection in SCIM" 2020 IEEE International Conference on Environment and Electrical Engineering and 2020 IEEE Industrial and Commercial Power Systems Europe (EEEIC/I&CPS Europe), 9th-12th June 2020, Madrid, Spain.
Sinha Ashish Kumar, Kumar Prashant, Prince and Hati, Ananda Shankar, "ANN Based Fault Detection Scheme for Bearing Condition Monitoring in SRIMs using FFT, DWT and Band-pass Filters" 2020 International Conference on Power, Instrumentation, Control, and Computing (PICC) 2020 IEEE.
Prince Kumar and Hati, Ananda Shankar, "Sensor-less Speed Control of Ventilation System Using Extended Kalman Filter For High Performance," 2021 IEEE 8th Uttar Pradesh Section International Conference on Electrical, Electronics and Computer Engineering (UPCON), 2021, pp. 1-6.
Kumar Prashant and Hati, Ananda Shankar "Support Vector Classifiers based broken rotor bar detection in Squirrel cage induction motor" Machines, Mechanisms and Robotics, Springer, Singapore, 429-438.
Hati, Ananda Shankar, and Chatterjee, T. K., "Some studies on condition monitoring techniques for online condition monitoring and fault diagnosis of mine winder motor", International Journal of Engineering Science and Technology (IJEST), vol. 4, no. 08, pp. 3785-3793, August 2012.
Hati, Ananda Shankar, and Chatterjee, T. K., "Axial leakage flux-based online condition monitoring instrumentation system for mine winder motor" Journal of Mines, Metals & Fuels, vol. 63, no. 5&6, pp. 132-140, May-June 2015.
Hati, Ananda Shankar, and Chatterjee, T. K., "Current monitoring Instrumentation system for detecting airgap eccentricity in mine winder motor", International Journal of Applied Engineering Research, vol. 10, no. 22, pp. 43000-43007, 2015.
Hati, Ananda Shankar, "Vibration monitoring instrumentation system for detecting airgap eccentricity in mine winder motor" Journal of Mine Metals and Fuels, vol. 64, no. 5&6, pp. 240-248, May-June 2016.
S. A. Haider et al., “Energy-Efficient Self-Supervised Technique to Identify Abnormal User over 5G Network for E-Commerce,” IEEE Transactions on Consumer Electronics, vol. 2024, pp. 1–1.
V. Chunduri, A. Kumar, A. Joshi, S. R. Jena, A. Jumaev, and S. More, “Optimizing energy and latency trade-offs in mobile ultra-dense IoT networks within futuristic smart vertical networks,” Int. J. Data Sci. Anal., 2023.
Sudheesh et al., “Bidirectional encoder representations from transformers and deep learning model for analyzing smartphone-related tweets,” PeerJ Comput. Sci., vol. 9, no. e1432, p. e1432, 2023.
Sudheesh et al., “Analyzing sentiments regarding ChatGPT using novel BERT: A machine learning approach,” Information (Basel), vol. 14, no. 9, p. 474, 2023.
Rao, D. P., Yadav, H. S., Yadava, A. K., Singh, S., & Yadav, U. (2011). In-situ preparation of macrocyclic complexes of dioxomolybdenum(VI) involving a heterocyclic precursor. Journal of Coordination Chemistry, 64(2), 293–299.
Rao, D. P., Yadav, H. S., Yadava, A. K., Singh, S., & Yadav, U. (2012). Syntheses and spectroscopic studies on macrocyclic complexes of dioxomolybdenum(vi) with furil as precursor. E-Journal of Chemistry, 9(2), 497–503.
Yadava, A. K., Yadav, H. S., Yadav, U., & Rao, D. P. (2012). Synthesis and structural characterization of novel square pyramidal oxovanadium(IV) complexes with ligands having N and O donor atoms. Turkish Journal of Chemistry.
Yadava, A. K., Yadav, H. S., Singh, S., Yadav, U., & Rao, D. P. (2013). Synthesis and characterization of some novel Schiff base complexes of Oxovanadium(IV) cation. Journal of Chemistry, 2013, 1–5.
Rao, D. P., Yadav, H. S., Yadava, A. K., Singh, S., & Yadav, U. (2012). Synthesis and characterization of cis-dioxomolybdenum(VI) complexes having furil as precursor molecule. Journal of the Serbian Chemical Society, 77(9), 1205–1210.
Singh, S., Yadav, H. S., Yadava, A. K., & Rao, D. P. (2013). Synthesis of oxovanadium(iv) complexes with tetraaza coordinating ligands. Journal of Chemistry, 1–5.
Rao, D. P. (2019). A review on versatile applications of novel Schiff bases and their metal complexes. Letters in Applied NanoBioScience, 8(4), 675–681.
Kumar, P., Kamle, M., Singh, J., & Rao, D. P. (2008). Isolation and characterization of peroxidase from the leaves of Ricinus communis. J Biotech Biochem, 4(4), 283-292.
Rao, D. P., Srivastav, S. K., Prasad, C., Saxena, R., & Asthana, S. (2010). Role of nanoparticles in drug delivery. International Journal of Nanotechnology and Applications, 4(1), 45-49.
Pallavi Mittal, P. M., Madhu Kamle, M. K., Shubhangini Sharma, S. S., Pooja Choudhary, P. C., Rao, D. P., & Pradeep Kumar, P. K. (2017). Plant growth-promoting rhizobacteria (PGPR): mechanism, role in crop improvement and sustainable agriculture. In Advances in PGPR research (pp. 386-397). Wallingford UK: CABI.
Singh, A. P., & Rao, D. P. (2013). Assessment of tannery effluent: a case study of Kanpur in India. European Chemical Bulletin, 2(7), 461-464.
Gautam, R. K., Singh, C. P., & Rao, D. P. (2022). cis-Dioxomolybdenum (VI) complexes with N-donor macrocyclic ligands. Biointerface Res Appl Chem, 12(1), 1352-1364.
Rao, D. P., Yadav, H. S., & Singh, C. P. (2021). Molybdenum (VI) complexes with Schiff base containing N-hetero atom. Lett. Appl. NanoBioScience., 10(1), 1816-1824.
Khilji et al., “Titanium Alloy Particles Formation in Electrical Discharge Machining and Fractal Analysis,” JOM 2021 742, vol. 74, no. 2, pp. 448–455, Jan. 2022.
I. A. Khilji, S. N. B. M. Safee, S. Pathak, C. R. Chilakamarry, A. S. B. A. Sani, and V. J. Reddy, “Facile Manufacture of Oxide-Free Cu Particles Coated with Oleic Acid by Electrical Discharge Machining,” Micromachines 2022, Vol. 13, Page 969, vol. 13, no. 6, p. 969, Jun. 2022.
I. A. Khilji, C. R. Chilakamarry, A. N. Surendran, K. Kate, and J. Satyavolu, “Natural Fiber Composite Filaments for Additive Manufacturing: A Comprehensive Review,” Sustain. 2023, Vol. 15, Page 16171, vol. 15, no. 23, p. 16171, Nov. 2023.
C. R. Chilakamarry, A. M. Mimi Sakinah, A. W. Zularism, I. A. Khilji, and S. Kumarasamy, “Glycerol Waste to Bio-Ethanol: Optimization of Fermentation Parameters by the Taguchi Method,” J. Chem., vol. 2022, p. 4892992, 2022.
C. R. Chilakamarry, A. M. M. Sakinah, A. W. Zularism, I. A. Khilji, and R. Sirohi, “Bioconversion of glycerol waste to ethanol by Escherichia coli and optimisation of process parameters,” Indian J. Exp. Biol., vol. 60, no. September, pp. 681–688, 2022.
Bharat, P. V., & Chakravarti, M. (2014). RF harvesting circuitry for ambient backscatter technology. International Journal of Applied Eengineering Research, 5769–5778.
Chakravarthi, M. Kalyan, Pannem, V. K., & Venkatesan, N. (2014). Real Time Implementation of Gain Scheduled Controller Design for Higher Order Nonlinear System Using LabVIEW. IJET, 6(5).
Chakravarthi, M. Kalyan, & Venkatesan, N. (2014). Labview Based Tuning Of Pi Controllers For A Real Time Non Linear Process. Journal of Theoretical & Applied Information Technology, 68(3).
Chakravarthi, M. Kalyan, & Venkatesan, N. (2015c). Experimental validation of a multi model PI controller for a non linear hybrid system in LabVIEW. Telkomnika, 13(2), 547–555.
Chakravarthi, M. Kalyan, & Venkatesan, N. (2015b). Design and Implementation of Lab View Based Optimally Tuned PI Controller for A Real Time Non Linear Process. Asian Journal of Scientific Research, 8(1), 95.
Mohammed, S., Naveed, S., Chakravarthi, M. K., & Venkatesan, N. (2015). Comparative study of controller performance for different real-time hybrid models. IEEE.
Supritha, R., Kalyan Chakravarthi, M., & Ali, S. R. (2016). An embedded visually impaired reconfigurable author assistance system using LabVIEW. Springer India.
Pannem, V. K., KalyanChakravarthi, M., & Venkatesan, N. (2015). Validation of integer and fractional order PI controllers for a real time non linear process. IEEE.
Chakravarthi, M. Kalyan, Gupta, K., Malik, J., & Venkatesan, N. (2015b). Linearized PI controller for real-time delay dominant second order nonlinear systems. IEEE.
Chakravarthi, M. Kalyan, & Venkatesan, N. (2015a). Design and implementation of adaptive model based gain scheduled controller for a real time non linear system in LabVIEW. Research Journal of Applied Sciences, Engineering and Technology, 10(2), 188–196.
Chakravarthi, M. Kalyan, Bharath, B., & Sreehari, R. V. (2015). Implementation of an automated drug delivery system using linear actuator. IEEE.
Ruttala, U. K., Balamurugan, M. S., & Chakravarthi, M. K. (2015). NFC based smart campus payment system. Indian Journal of Science and Technology, 8(19), 1–5.
Sudheer, G. S., Prasad, C. R., Chakravarthi, M. K., & Bharath, B. (2015). Vehicle Number Identification and Logging System Using Optical Character Recognition. International Journal of Control Theory and Applications, 9(14), 267–272.
Bais, N., Shubha, R., Yamuna, V., & Chakravarthi, M. K. (2018). Smart Mobile Diagnostic Laboratory and Doctor Annunciation System in Ambulances. Springer Singapore.
Chakravarthi, M. Kalyan, & Venkatesan, N. (2018). Adaptive type-2 fuzzy controller for nonlinear delay dominant MIMO systems: an experimental paradigm in LabVIEW. International Journal of Advanced Intelligence Paradigms, 10(4), 354–373.
Chakravarthi, M. Kalyan, Tiwari, R. K., & Handa, S. (2015). Accelerometer based static gesture recognition and mobile monitoring system using neural networks. Procedia Computer Science, 70, 683–687.
Sathyaseelan, M. P., Chakravarthi, M. K., Sathyaseelan, A. P., & Sudipta, S. (2021). IoT based COVID De-Escalation System using Bluetooth Low Level Energy. IEEE.
Karthik, M. V., Chakravarthi, M. K., Yapanto, L. M., Selvapandian, D., Harish, R., & Subramani, K. (2021). Optical Analysis of the UPQC using PI Controller in Power flow System. IEEE.
Sharma, D. K., Singh, B., Regin, R., Steffi, R., & Chakravarthi, M. K. (2021). Efficient Classification for Neural Machines Interpretations based on Mathematical models. IEEE.
Chakravarthi, M. Kalyan, Watekar, P. R., Babu, A. V., Sateesh, M., & Reddy, P. V. (2012). Optimization of Silica Glass Micro Fiber for Zero Dispersion Wavelength.
Praveen Barmavatu, Mihir Kumar Das, Rathod Subhash, Banoth Sravanthi, Radhamanohar Aepuru, R Venkat reddy, Yalagandala akshay kumar "Designing an Effective Plate Fin Heat Exchanger and Prediction of Thermal Performance Operated Under Different Water Blends Using Machine Learning", Journal of Thermal Sciences and Engineering Applications, ASME Publications, Vol-15/issue-4/pp: 041001-041022, 2023.
Praveen Barmavatu, S A Deshmukh, Mihir Kumar Das, Radhamanohar Aepuru, R Venkat reddy, Banoth Sravanthi “Synthesis and experimental investigation of glass fiber epoxy/saw dust composites for flexural & tensile strength”, Materiale Plastice, vol-59/issue-02/pp:73-81/June 2022.
U.B. Vishwanatha, Y. Dharmendar Reddy, Praveen Barmavatu, B. Shankar Goud “Insights into stretching ratio and velocity slip on MHD rotating flow of Maxwell nanofluid over a stretching sheet: Semi-analytical technique OHAM”, Journal of the Indian Chemical Society, Elsevier Publishers, , Vol-100/issue-3/pp: 100937-10, 2023.
Darapu Kiran Sagar Reddy, Praveen Barmavatu, Mihir Kumar Das, Radhamanohar Aepuru “Mechanical properties evaluation and microstructural analysis study of ceramic-coated IC engine cylinder liner”, Elsevier material today proceedings, Vol-76/Part-3, pp: 518-523, 2023.
Darapu Kiran Sagar Reddy, Praveen Barmavatu, Mihir Kumar Das, Radhamanohar “Aepuru Experimental analysis of coated engine cylinder liners”, AIP Conference Proceedings, ISSN 1551-7616/ Vol 2786/ Paper ID: 030002, 2023.
Sonali Anant Deshmukh, Praveen Barmavatu, Mihir Kumar Das, Bukke Kiran Naik, Radhamanohar Aepuru “Heat Transfer Analysis in Liquid Jet Impingement for Graphene/Water Nano Fluid”, Springer Lecture Notes in Mechanical Engineering (LNME), ICETMIE-2022, pp: 1079–1090.
Barmavatu Praveen, Madan mohan reddy Nune, Yalagandala akshay kumar, Rathod Subhash, “Investigating the Effect of Minimum Quantity Lubrication on Surface Finish of EN 47 Steel Material”, Elsevier material today proceedings, , Vol-38/Part-05, pp-32-53-3257.
Yalagandala akshay kumar, Shaik shafee, Barmavatu Praveen “Experimental investigation of residual stresses in a die casted alluminium fly wheel” Elsevier material today proceedings /vol19/issue-Part-02/pp: A10-A18/October2019, Impact Factor- 2.59.
Barmavatu Praveen & S. chakradhar Goud “fabrication of compact heat exchanger with composite alloys” International journal of innovative technology and exploring engineering, 8(6S4), 717–721.
Barmavatu Praveen, Yalagandala Akshay Kumar, Banoth Sravanthi, H. Ameresh “Methodological Investigation on recycling of Plastic Polymers-A Review” International journal of scientific & technological research 2277-8616/vol-9/issue-03/pp:1537-1542/march 2020.
Barmavatu Praveen & s chakradhar goud “CFD approach for different fluids varients in compact heat exchanger at different parametric conditions” International journal of scientific & technological research, /vol-8/issue-12/pp:2288-2296/december2019. https://www.ijstr.org/paper-references.php?ref=IJSTR-1119-24385
G. Aziz, S. Sarwar, R. Waheed, and M. S. Khan, “The significance of renewable energy, globalization, and agriculture on sustainable economic growth and green environment: Metaphorically, a two-sided blade,” Nat. Resour. Forum, no. April, pp. 1–21, 2023.
N. Elouaer, R. Waheed, S. Sarwar, and G. Aziz, “Does Gender Diversity and Experience Moderate the Impact of Tax Aggressiveness on Corporate Social Responsibility: A Study of UAE Listed Companies,” Sustainability, vol. 14, no. 21, p. 14348, Nov. 2022.
G. Aziz, S. Sarwar, R. Waheed, and M. S. Khan, “Significance of hydrogen energy to control the environmental gasses in light of COP26: A case of European Countries,” Resour. Policy, vol. 80, no. September 2022, p. 103240, 2023.
G. Aziz, R. Waheed, S. Sarwar, and M. S. Khan, “The Significance of Governance Indicators to Achieve Carbon Neutrality: A New Insight of Life Expectancy,” Sustainability, vol. 15, no. 1, pp. 1–20, 2023.
A, V. V. ., T, S. ., S, S. N. ., & Rajest, D. S. S. . (2022). IoT-Based Automated Oxygen Pumping System for Acute Asthma Patients. European Journal of Life Safety and Stability (2660-9630), 19 (7), 8-34.
A. Qadeer, M. Wasim, H. Ghazala, A. Rida, and W. Suleman, “Emerging trends of green hydrogen and sustainable environment in the case of Australia,” Environ. Sci. Pollut. Res., 2023.
A. T. Hoang and V. V. Pham, “A study on a solution to reduce emissions by using hydrogen as an alternative fuel for a diesel engine integrated exhaust gas recirculation,” in International Conference on Emerging Applications in Material Science and Technology: ICEAMST2020, 2020, p. 020035.
A. T. Hoang, V. V Le, A. X. Nguyen, and D. N. Nguyen, “A Study On The Changes In Microstructure And Mechanical Properties Of Multi-Pass Welding Between 316 Stainless Steel And Low-Carbon Steel,” Journal of Advanced Manufacturing Technology (JAMT), vol. 12, no. 2, pp. 25–40, 2018.
D. Cai, G. Aziz, S. Sarwar, M. I. Alsaggaf, and A. Sinha, “Applicability of denoising based artificial intelligence to forecast the environmental externalities,” Geosci. Front., p. 101740, 2023.
G. Aziz and S. Sarwar, “Empirical Evidence of Environmental Technologies , Renewable Energy and Tourism to Minimize the Environmental Damages : Implication of Advanced Panel Analysis,” Int. J. Environ. Res. Public Health, vol. 20, no. 6, p. 5118, 2023.
G. Aziz and S. Sarwar, “Revisit the role of governance indicators to achieve sustainable economic growth of Saudi Arabia–pre and post implementation of 2030 Vision,” Struct. Chang. Econ. Dyn., vol. 66, pp. 213–227, 2023.
G. Aziz, S. Sarwar, K. Nawaz, R. Waheed, and M. S. Khan, “Influence of tech-industry, natural resources, renewable energy and urbanization towards environment footprints: A fresh evidence of Saudi Arabia,” Resour. Policy, vol. 83, p. 103553, Jun. 2023.
G. Aziz, S. Sarwar, M. Shahbaz, M. N. Malik, and R. Waheed, “Empirical relationship between creativity and carbon intensity: a case of OPEC countries,” Environ. Sci. Pollut. Res., vol. 30, no. 13, pp. 38886–38897, Mar. 2023.
G. Aziz, S. Sarwar, M. W. Hussan, and A. Saeed, “The importance of extended-STIRPAT in responding to the environmental footprint: Inclusion of environmental technologies and environmental taxation,” Energy Strateg. Rev., vol. 50, no. May, p. 101216, 2023.
H.A.A. Alsultan , F.H.H. Maziqa and M.R.A. Al-Owaidi "A stratigraphic analysis of the Khasib, Tanuma and Sa’di formations in the Majnoon oil field, southern Iraq," Bulletin of the Geological Society of Malaysia, vol. 73, p.163 – 169, 2022 .
H.A.A. Alsultan , M.L. Hussein, , M.R.A. Al-Owaidi , A.J. Al-Khafaji and M.A. Menshed "Sequence Stratigraphy and Sedimentary Environment of the Shiranish Formation, Duhok region, Northern Iraq", Iraqi Journal of Science, vol.63, no.11, p.4861-4871, 2022.
H.A.A. Alsultan and K. H. Awad "Sequence Stratigraphy of the Fatha Formation in Shaqlawa Area, Northern Iraq," Iraqi Journal of Science ,vol. 54, no.2F, p.13-21, 2021.
I.I. Mohammed, and H. A. A. Alsultan "Facies Analysis and Depositional Environments of the Nahr Umr Formation in Rumaila Oil Field, Southern Iraq," Iraqi Geological Journal, vol.55, no.2A, p.79-92, 2022.
I.I. Mohammed, and H. A. A. Alsultan "Stratigraphy Analysis of the Nahr Umr Formation in Zubair oil field, Southern Iraq," Iraqi Journal of Science, vol. 64, no. 6, p. 2899-2912, 2023.
Jerusha Angelene Christabel G, Shynu T, S. Suman Rajest, R. Regin, & Steffi. R. (2022). The use of Internet of Things (Iot) Technology in the Context of “Smart Gardens” is Becoming Increasingly Popular. International Journal of Biological Engineering and Agriculture, 1(2), 1–13.
L. Lei, G. Aziz, S. Sarwar, R. Waheed, and A. K. Tiwari, “Spillover and portfolio analysis for oil and stock market: A new insight across financial crisis, COVID-19 and Russian-Ukraine war,” Resour. Policy, vol. 85, p. 103645, Aug. 2023.
L. Qin, G. Aziz, M. W. Hussan, A. Qadeer, and S. Sarwar, “Empirical evidence of fintech and green environment: Using the green finance as a mediating variable,” Int. Rev. Econ. Financ., vol. 89, no. PA, pp. 33–49, 2023.
N. Kaur and S. D. Tiwari, “Estimation of magnetic anisotropy constant of magnetic nanoparticles,” in DAE Solid State Physics Symposium 2019, 2020.
N. Kaur and S. D. Tiwari, “Evidence for spin-glass freezing in NiO nanoparticles by critical dynamic scaling,” J. Supercond. Nov. Magn., vol. 34, no. 5, pp. 1545–1549, 2021.
N. Kaur and S. D. Tiwari, “Role of particle size distribution and magnetic anisotropy on magnetization of antiferromagnetic nanoparticles,” J. Phys. Chem. Solids, vol. 123, pp. 279–283, 2018.
N. Kaur and S. D. Tiwari, “Role of wide particle size distribution on magnetization,” Appl. Phys. A Mater. Sci. Process., vol. 126, no. 5, 2020.
N. Kaur and S. D. Tiwari, “Thermal decomposition of ferritin core,” Appl. Phys. A Mater. Sci. Process., vol. 125, no. 11, 2019.
O. Fabela, S. Patil, S. Chintamani, and B. H. Dennis, “Estimation of effective thermal conductivity of porous media utilizing inverse heat transfer analysis on cylindrical configuration,” in Volume 8: Heat Transfer and Thermal Engineering, 2017.
Priscila, S. S., Rajest, S. S., T, S. and G, G. (2022) “An Improvised Virtual Queue Algorithm to Manipulate the Congestion in High-Speed Network”, Central Asian Journal of Medical and Natural Science, 3(6), pp. 343-360.
R. Regin, Steffi. R, Jerusha Angelene Christabel G, Shynu T, S. Suman Rajest (2022), “Internet of Things (IoT) System Using Interrelated Computing Devices in Billing System”, Journal of Advanced Research in Dynamical and Control Systems, Vol.14, no.1, pp. 24-40.
R. Steffi, G. Jerusha Angelene Christabel, T. Shynu, S. Suman Rajest, R. Regin (2022), “ A Method for the Administration of the Work Performed by Employees”, Journal of Advanced Research in Dynamical and Control Systems, Vol.14, no.1, pp. 7-23.
Rajest, S. S. ., Regin, R. ., T, S. ., G, J. A. C. ., & R, S. . (2022). Production of Blockchains as Well as their Implementation. Vital Annex : International Journal of Novel Research in Advanced Sciences, 1(2), 21–44.
Regin, D. R., Rajest, D. S. S., T, S., G, J. A. C., & R, S. (2022). An Automated Conversation System Using Natural Language Processing (NLP) Chatbot in Python. Central Asian Journal Of Medical And Natural Sciences, 3(4), 314-336.
S. Patil, S. Chintamani, B. H. Dennis, and R. Kumar, “Real time prediction of internal temperature of heat generating bodies using neural network,” Therm. Sci. Eng. Prog., vol. 23, no. 100910, p. 100910, 2021.
S. Patil, S. Chintamani, J. Grisham, R. Kumar, and B. H. Dennis, “Inverse determination of temperature distribution in partially cooled heat generating cylinder,” in Volume 8B: Heat Transfer and Thermal Engineering, 2015.
S. S. Rajest, R. Regin, S. T, J. A. C. G, and S. R, “Improving Infrastructure and Transportation Systems Using Internet of Things Based Smart City”, CAJOTAS, vol. 3, no. 9, pp. 125-141, Sep. 2022.
S. Sarwar, G. Aziz, and A. Kumar Tiwari, “Implication of machine learning techniques to forecast the electricity price and carbon emission: Evidence from a hot region,” Geosci. Front., no. xxxx, p. 101647, 2023.
S. Sarwar, G. Aziz, and D. Balsalobre-Lorente, “Forecasting Accuracy of Traditional Regression , Machine Learning , and Deep Learning : A Study of Environmental Emissions in Saudi Arabia,” Sustainability, vol. 15, no. 20, p. 14957, 2023.
S. Sarwar, R. Waheed, G. Aziz, and S. A. Apostu, “The Nexus of Energy, Green Economy, Blue Economy, and Carbon Neutrality Targets,” Energies, vol. 15, no. 18, p. 6767, Sep. 2022.
T, S., Rajest, S. S., Regin, R., Christabel G, J. A., & R, S. (2022). Automation And Control Of Industrial Operations Using Android Mobile Devices Based On The Internet Of Things. Central Asian Journal of Mathematical Theory and Computer Sciences, 3(9), 1-33.
X. D. Pham, A. T. Hoang, and D. N. Nguyen, “A Study on the Effect of the Change of Tempering Temperature on the Microstructure Transformation of Cu-Ni-Sn Alloy,” International Journal of Mechanical & Mechatronics Engineering, vol. 18, no. 04, pp. 27–34, 2018.
Y. Cui, G. Aziz, S. Sarwar, R. Waheed, Z. Mighri, and U. Shahzad, “Reinvestigate the significance of STRIPAT and extended STRIPAT: An inclusion of renewable energy and trade for gulf council countries,” Energy Environ., p. 0958305X231181671, Jun. 2023
T. Kaur, S. Mahajan, S. Verma, Priyanka and J. Gambhir, “Arduino based low cost active dual axis solar tracker,” 2016 IEEE 1st International Conference on Power Electronics, Intelligent Control and Energy Systems (ICPEICES), Delhi, India, 2016, pp. 1-5.
M. H. M. Sidek, N. Azis, W. Z. W. Hasan, M. Z. A. Ab Kadir, S. Shafie, and M. A. M. Radzi, “Automated positioning dual-axis solar tracking system with precision elevation and azimuth angle control,” Energy (Oxf.), vol. 124, pp. 160–170, 2017.
Q. Ha and M. D. Phung, “IoT‐enabled dependable control for solar energy harvesting in smart buildings,” IET Smart Cities, vol. 1, no. 2, pp. 61–70, 2019.
S. M. Fatemi, M. S. Shadlu and A. Talebkhah, “A New Method for Maximum Power Point Tracking in Solar PV Systems by Combining Extremum Seeking Method (ESM) and Model Predictive Control (MPC),” 2020 11th Power Electronics, Drive Systems, and Technologies Conference (PEDSTC), Tehran, Iran, 2020, pp. 1-5.
R. Medhane, S. Dhamal, and M. Thakre, “Solar photovoltaic water pumping system with reduced sensors and IMD using the P&O MPPT algorithm,” SSRN Electron. J., 2021.
M. Qenawy, W. Zhou, and Y. Liu, “Effects of crossflow-fed-shaped holes on the adiabatic film cooling effectiveness,” International Journal of Thermal Sciences, vol. 177, p. 107578, Jul. 2022.
M. Qenawy, W. Zhou, D. Peng, and Y. Liu, “Investigation of Film Cooling Vortical Structures Behind a Cylindrical Hole Fed by an Internal Crossflow,” Sep. 2019.
M. Qenawy, M. Taha, and A. H. Abdelbaky Elbatran, “Unsteady adiabatic film cooling effectiveness behind shaped holes,” Case Studies in Thermal Engineering, vol. 34, p. 102005, Jun. 2022.
M. Qenawy, A. Hamed, W. Abdelfadeel, and S. Abdelhady, “Assessment of the Planned Expansion of Renewable Energy in Egypt,” International Journal of Applied Energy Systems, vol. 0, no. 0, pp. 0–0, Apr. 2022.
M. Qenawy, Y. Chen, J. Wang, J. Tian, and B. Chen, “Intermittent cryogen spray cooling coupled with cold air jet for heat transfer enhancement and cryogen saving of laser dermatology,” Physics of Fluids, vol. 36, no. 2, Feb. 2024.
M. Qenawy, J. Wang, J. Tian, B. Li, and B. Chen, “Investigation of unsteady flow behavior of cryogen-spray coupled with cold air jet,” Appl Therm Eng, vol. 235, Nov. 2023.
M. Qenawy, M. Taha, J. Wang, and A. H. Abdelbaky Elbatran, “Effects of hole-inlet velocity on the adiabatic film cooling effectiveness behind crossflow-fed shaped holes,” Appl Therm Eng, vol. 222, Mar. 2023.
M. Qenawy, W. Zhou, H. Chen, H. Shao, D. Peng, and Y. Liu, “Unsteady Analysis of Adiabatic Film Cooling Effectiveness Behind a Row of Circular Holes Fed by Internal Crossflow,” in Volume 5B: Heat Transfer, American Society of Mechanical Engineers, Jun. 2019.
M. Qenawy, Y. Chen, J. Wang, J. Tian, B. Li, and B. Chen, “Transient behavior of liquid film deposition and surface heat transfer upon cryogen-spray cooling coupled with cold air jet,” Int J Heat Mass Transf, vol. 223, p. 125224, May 2024.
W. Zhou, M. Qenawy, H. Shao, D. Peng, X. Wen, and Y. Liu, “Turbine vane endwall film cooling with barchan-dune shaped ramp in a single-passage transonic wind tunnel,” Int J Heat Mass Transf, vol. 162, Dec. 2020.
W. Zhou, H. Shao, M. Qenawy, D. Peng, H. Hu, and Y. Liu, “Improved Turbine Vane Endwall Film Cooling by Using Sand-Dune-Inspired Design,” Journal of Thermal Science, vol. 31, no. 3, pp. 958–973, May 2022.
J. Tian et al., “Unstable spray pattern and cooling performance of cryogen spray coupled with cold air jet: An experimental study,” Physics of Fluids, vol. 35, no. 12, Dec. 2023.
H. S. El-Mesery, M. Qenawy, Z. Hu, and W. G. Alshaer, “Evaluation of infrared drying for okra: Mathematical modelling, moisture diffusivity, energy activity and quality attributes,” Case Studies in Thermal Engineering, vol. 50, p. 103451, Oct. 2023.
M. Qenawy et al., “Performance and emission of extracted biodiesel from mixed Jatropha-Castor seeds,” Fuel, vol. 357, p. 130060, Feb. 2024.
M. Qenawy, Y. Liu, and W. Zhou, “On the unsteady behaviours of the adiabatic endwall film cooling effectiveness,” IOP Conf Ser Mater Sci Eng, vol. 1172, no. 1, p. 012031, Aug. 2021.
M. Qenawy and S. Abdelhady, “Analytical Study of a Modified Thermal Energy Storage System for PS10 in Aswan,” in The International Conference on Mathematics and Engineering Physics, May 2014, pp. 1–5.
Mohamed Qenawy, “Matlab Simulation of 10 MW Molten Salt Solar Power Tower Plant in Aswan,” Noble International Journal of Scientific Research, vol. 1, no. 1, pp. 34–43, 2017.
Mohamed Qenawy, S. Abdelhady, W. Abdelfadeel, and M. Shaban, “Analytical Study of a Modified PS10 in Aswan,” Int J Sci Eng Res, vol. 5, no. 9, pp. 976–983, 2014.
H. Chen, W. Zhou, M. Qenawy, and Y. Liu, “Experimental Study on Spatio-Temporal Variation of Double-Row Holes Film Cooling Effectiveness with Oscillating Mainstream,” Sep. 2019.
W. Zhou, M. Qenawy, Y. Liu, X. Wen, and D. Peng, “Influence of mainstream flow oscillations on spatio-temporal variation of adiabatic film cooling effectiveness,” Int J Heat Mass Transf, vol. 129, pp. 569–579, Feb. 2019.
M. Qenawy, L. Yuan, Y. Liu, D. Peng, X. Wen, and W. Zhou, “A Novel Single-Passage Transonic Wind Tunnel for Turbine-Vane Film Cooling,” J Eng Gas Turbine Power, vol. 142, no. 7, Jul. 2020.
M. Qenawy, H. Chen, D. Peng, Y. Liu, and W. Zhou, “Flow Structures and Unsteady Behaviors of Film Cooling from Discrete Holes Fed by Internal Crossflow,” J Turbomach, vol. 142, no. 4, Apr. 2020.
M. Qenawy, W. Zhou, and Y. Liu, “Effects of crossflow-fed-shaped holes on the adiabatic film cooling effectiveness,” International Journal of Thermal Sciences, vol. 177, p. 107578, Jul. 2022.
Ananda Shankar Hati, and T. K. Chatterjee, "Symmetrical component filter based online condition monitoring instrumentation system for mine winder motor" Measurement (Elsevier), vol. 82, pp. 284-300, 2016.
Prashant Kumar and Ananda Shankar Hati "Review on Machine Learning Algorithm Based Fault Detection in Induction Motors," Archives of Computational Methods in Engineering, vol: 28, pp: 1929-1940, 2021.
Kumar Prashant and Hati, Ananda Shankar "Convolutional Neural Network with batch normalization for fault detection in SCIM," IET Electric Power Application, vol: 15, issue: 1, pp. 39-50, 2021.
Kumar Prashant and Hati, Ananda Shankar "Deep Convolutional Neural Network based on adaptive gradient optimizer for fault detection in SCIM," ISA Transactions, vol: 111, pp: 350-359, 2021.
Prince, Hati Ananda Shankar, Chakrabarti Prasun, Abawajy Jemal Hussein and Ng Wee Keong "Development of Energy Efficient Drive for Ventilation System using Recurrent Neural Network," Neural Computing and Applications, Vol. 33, no. 14, pp. 8659-8668, 2021.
Sinha Ashish Kumar, Hati Ananda Shankar, Benbouzid Mohamed and Chakrabarti Prasun "ANN-based Pattern Recognition for Induction Motor Broken Rotor Bar Monitoring under Supply Frequency Regulation" Machines (2021), vol: 9(5).
Prince and Hati Ananda Shankar "A Comprehensive Review of Energy-Efficiency of Ventilation System using Artificial Intelligence" Renewable and Sustainable Energy Reviews (2021), vol: 146, 2021.
Kumar Prashant and Hati, Ananda Shankar "Transfer Learning Based Deep CNN Model for Multiple Faults Detection in SCIM" Neural Computing and Applications (2021).
Prince and Hati Ananda Shankar "Temperature and Humidity Dependent MRAS Based Speed Estimation Technique for Induction Motor used in Mine Ventilation Drive" Journal of Mining Science, 2021, Vol. 57, No. 5, pp. 842–851.
Kumar Prashant and Hati, Ananda Shankar "Dilated Convolutional Neural Network Based Model For Bearing Faults and Broken Rotor Bar Detection in Squirrel Cage Induction Motors" Expert Systems With Applications (2022).
Prince and Hati Ananda Shankar "Convolutional Neural Network-Long Short Term Memory Optimization for Accurate Prediction of Airflow in a Ventilation System" Expert Systems with Applications (2022).
Vatsa Aniket and Hati Ananda Shankar "Depolarization Current Prediction of Transformers OPI System Affected From Detrapped Charge Using LSTM," in IEEE Transactions on Instrumentation and Measurement, vol. 71, pp. 1-11, 2022, Art no. 2511711.
Gorai Rahul, Hati Ananda Shankar, and Maity Tanmoy, "A new cascaded multilevel converter topology with a reduced number of components" 3rd IEEE 2017 Conference on International conference on Power, Control, Signals and Instrumentation Engineering (ICPCSI-2017), 21-22 September 2017 | IEEE, Chennai, India., pp. 539-543.
Kumar Prashant, Hati, Ananda Shankar, Sanjeevikumar Padmanaban, Leonowicz Zbigniew and Prasun Chakrabarti "Amalgamation of Transfer Learning and Deep Convolutional Neural Network for Multiple Fault Detection in SCIM" 2020 IEEE International Conference on Environment and Electrical Engineering and 2020 IEEE Industrial and Commercial Power Systems Europe (EEEIC/I&CPS Europe), 9th-12th June 2020, Madrid, Spain.
Sinha Ashish Kumar, Kumar Prashant, Prince and Hati, Ananda Shankar, "ANN Based Fault Detection Scheme for Bearing Condition Monitoring in SRIMs using FFT, DWT and Band-pass Filters" 2020 International Conference on Power, Instrumentation, Control, and Computing (PICC) 2020 IEEE.
Prince Kumar and Hati, Ananda Shankar, "Sensor-less Speed Control of Ventilation System Using Extended Kalman Filter For High Performance," 2021 IEEE 8th Uttar Pradesh Section International Conference on Electrical, Electronics and Computer Engineering (UPCON), 2021, pp. 1-6.
Kumar Prashant and Hati, Ananda Shankar "Support Vector Classifiers based broken rotor bar detection in Squirrel cage induction motor" Machines, Mechanisms and Robotics, Springer, Singapore, 429-438.
Hati, Ananda Shankar, and Chatterjee, T. K., "Some studies on condition monitoring techniques for online condition monitoring and fault diagnosis of mine winder motor", International Journal of Engineering Science and Technology (IJEST), vol. 4, no. 08, pp. 3785-3793, August 2012.
Hati, Ananda Shankar, and Chatterjee, T. K., "Axial leakage flux-based online condition monitoring instrumentation system for mine winder motor" Journal of Mines, Metals & Fuels, vol. 63, no. 5&6, pp. 132-140, May-June 2015.
Hati, Ananda Shankar, and Chatterjee, T. K., "Current monitoring Instrumentation system for detecting airgap eccentricity in mine winder motor", International Journal of Applied Engineering Research, vol. 10, no. 22, pp. 43000-43007, 2015.
Hati, Ananda Shankar, "Vibration monitoring instrumentation system for detecting airgap eccentricity in mine winder motor" Journal of Mine Metals and Fuels, vol. 64, no. 5&6, pp. 240-248, May-June 2016.
S. A. Haider et al., “Energy-Efficient Self-Supervised Technique to Identify Abnormal User over 5G Network for E-Commerce,” IEEE Transactions on Consumer Electronics, vol. 2024, pp. 1–1.
V. Chunduri, A. Kumar, A. Joshi, S. R. Jena, A. Jumaev, and S. More, “Optimizing energy and latency trade-offs in mobile ultra-dense IoT networks within futuristic smart vertical networks,” Int. J. Data Sci. Anal., 2023.
Sudheesh et al., “Bidirectional encoder representations from transformers and deep learning model for analyzing smartphone-related tweets,” PeerJ Comput. Sci., vol. 9, no. e1432, p. e1432, 2023.
Sudheesh et al., “Analyzing sentiments regarding ChatGPT using novel BERT: A machine learning approach,” Information (Basel), vol. 14, no. 9, p. 474, 2023.
Rao, D. P., Yadav, H. S., Yadava, A. K., Singh, S., & Yadav, U. (2011). In-situ preparation of macrocyclic complexes of dioxomolybdenum(VI) involving a heterocyclic precursor. Journal of Coordination Chemistry, 64(2), 293–299.
Rao, D. P., Yadav, H. S., Yadava, A. K., Singh, S., & Yadav, U. (2012). Syntheses and spectroscopic studies on macrocyclic complexes of dioxomolybdenum(vi) with furil as precursor. E-Journal of Chemistry, 9(2), 497–503.
Yadava, A. K., Yadav, H. S., Yadav, U., & Rao, D. P. (2012). Synthesis and structural characterization of novel square pyramidal oxovanadium(IV) complexes with ligands having N and O donor atoms. Turkish Journal of Chemistry.
Yadava, A. K., Yadav, H. S., Singh, S., Yadav, U., & Rao, D. P. (2013). Synthesis and characterization of some novel Schiff base complexes of Oxovanadium(IV) cation. Journal of Chemistry, 2013, 1–5.
Rao, D. P., Yadav, H. S., Yadava, A. K., Singh, S., & Yadav, U. (2012). Synthesis and characterization of cis-dioxomolybdenum(VI) complexes having furil as precursor molecule. Journal of the Serbian Chemical Society, 77(9), 1205–1210.
Singh, S., Yadav, H. S., Yadava, A. K., & Rao, D. P. (2013). Synthesis of oxovanadium(iv) complexes with tetraaza coordinating ligands. Journal of Chemistry, 1–5.
Rao, D. P. (2019). A review on versatile applications of novel Schiff bases and their metal complexes. Letters in Applied NanoBioScience, 8(4), 675–681.
Kumar, P., Kamle, M., Singh, J., & Rao, D. P. (2008). Isolation and characterization of peroxidase from the leaves of Ricinus communis. J Biotech Biochem, 4(4), 283-292.
Rao, D. P., Srivastav, S. K., Prasad, C., Saxena, R., & Asthana, S. (2010). Role of nanoparticles in drug delivery. International Journal of Nanotechnology and Applications, 4(1), 45-49.
Pallavi Mittal, P. M., Madhu Kamle, M. K., Shubhangini Sharma, S. S., Pooja Choudhary, P. C., Rao, D. P., & Pradeep Kumar, P. K. (2017). Plant growth-promoting rhizobacteria (PGPR): mechanism, role in crop improvement and sustainable agriculture. In Advances in PGPR research (pp. 386-397). Wallingford UK: CABI.
Singh, A. P., & Rao, D. P. (2013). Assessment of tannery effluent: a case study of Kanpur in India. European Chemical Bulletin, 2(7), 461-464.
Gautam, R. K., Singh, C. P., & Rao, D. P. (2022). cis-Dioxomolybdenum (VI) complexes with N-donor macrocyclic ligands. Biointerface Res Appl Chem, 12(1), 1352-1364.
Rao, D. P., Yadav, H. S., & Singh, C. P. (2021). Molybdenum (VI) complexes with Schiff base containing N-hetero atom. Lett. Appl. NanoBioScience., 10(1), 1816-1824.
Khilji et al., “Titanium Alloy Particles Formation in Electrical Discharge Machining and Fractal Analysis,” JOM 2021 742, vol. 74, no. 2, pp. 448–455, Jan. 2022.
I. A. Khilji, S. N. B. M. Safee, S. Pathak, C. R. Chilakamarry, A. S. B. A. Sani, and V. J. Reddy, “Facile Manufacture of Oxide-Free Cu Particles Coated with Oleic Acid by Electrical Discharge Machining,” Micromachines 2022, Vol. 13, Page 969, vol. 13, no. 6, p. 969, Jun. 2022.
I. A. Khilji, C. R. Chilakamarry, A. N. Surendran, K. Kate, and J. Satyavolu, “Natural Fiber Composite Filaments for Additive Manufacturing: A Comprehensive Review,” Sustain. 2023, Vol. 15, Page 16171, vol. 15, no. 23, p. 16171, Nov. 2023.
C. R. Chilakamarry, A. M. Mimi Sakinah, A. W. Zularism, I. A. Khilji, and S. Kumarasamy, “Glycerol Waste to Bio-Ethanol: Optimization of Fermentation Parameters by the Taguchi Method,” J. Chem., vol. 2022, p. 4892992, 2022.
C. R. Chilakamarry, A. M. M. Sakinah, A. W. Zularism, I. A. Khilji, and R. Sirohi, “Bioconversion of glycerol waste to ethanol by Escherichia coli and optimisation of process parameters,” Indian J. Exp. Biol., vol. 60, no. September, pp. 681–688, 2022.
Bharat, P. V., & Chakravarti, M. (2014). RF harvesting circuitry for ambient backscatter technology. International Journal of Applied Eengineering Research, 5769–5778.
Chakravarthi, M. Kalyan, Pannem, V. K., & Venkatesan, N. (2014). Real Time Implementation of Gain Scheduled Controller Design for Higher Order Nonlinear System Using LabVIEW. IJET, 6(5).
Chakravarthi, M. Kalyan, & Venkatesan, N. (2014). Labview Based Tuning Of Pi Controllers For A Real Time Non Linear Process. Journal of Theoretical & Applied Information Technology, 68(3).
Chakravarthi, M. Kalyan, & Venkatesan, N. (2015c). Experimental validation of a multi model PI controller for a non linear hybrid system in LabVIEW. Telkomnika, 13(2), 547–555.
Chakravarthi, M. Kalyan, & Venkatesan, N. (2015b). Design and Implementation of Lab View Based Optimally Tuned PI Controller for A Real Time Non Linear Process. Asian Journal of Scientific Research, 8(1), 95.
Mohammed, S., Naveed, S., Chakravarthi, M. K., & Venkatesan, N. (2015). Comparative study of controller performance for different real-time hybrid models. IEEE.
Supritha, R., Kalyan Chakravarthi, M., & Ali, S. R. (2016). An embedded visually impaired reconfigurable author assistance system using LabVIEW. Springer India.
Pannem, V. K., KalyanChakravarthi, M., & Venkatesan, N. (2015). Validation of integer and fractional order PI controllers for a real time non linear process. IEEE.
Chakravarthi, M. Kalyan, Gupta, K., Malik, J., & Venkatesan, N. (2015b). Linearized PI controller for real-time delay dominant second order nonlinear systems. IEEE.
Chakravarthi, M. Kalyan, & Venkatesan, N. (2015a). Design and implementation of adaptive model based gain scheduled controller for a real time non linear system in LabVIEW. Research Journal of Applied Sciences, Engineering and Technology, 10(2), 188–196.
Chakravarthi, M. Kalyan, Bharath, B., & Sreehari, R. V. (2015). Implementation of an automated drug delivery system using linear actuator. IEEE.
Ruttala, U. K., Balamurugan, M. S., & Chakravarthi, M. K. (2015). NFC based smart campus payment system. Indian Journal of Science and Technology, 8(19), 1–5.
Sudheer, G. S., Prasad, C. R., Chakravarthi, M. K., & Bharath, B. (2015). Vehicle Number Identification and Logging System Using Optical Character Recognition. International Journal of Control Theory and Applications, 9(14), 267–272.
Bais, N., Shubha, R., Yamuna, V., & Chakravarthi, M. K. (2018). Smart Mobile Diagnostic Laboratory and Doctor Annunciation System in Ambulances. Springer Singapore.
Chakravarthi, M. Kalyan, & Venkatesan, N. (2018). Adaptive type-2 fuzzy controller for nonlinear delay dominant MIMO systems: an experimental paradigm in LabVIEW. International Journal of Advanced Intelligence Paradigms, 10(4), 354–373.
Chakravarthi, M. Kalyan, Tiwari, R. K., & Handa, S. (2015). Accelerometer based static gesture recognition and mobile monitoring system using neural networks. Procedia Computer Science, 70, 683–687.
Sathyaseelan, M. P., Chakravarthi, M. K., Sathyaseelan, A. P., & Sudipta, S. (2021). IoT based COVID De-Escalation System using Bluetooth Low Level Energy. IEEE.
Karthik, M. V., Chakravarthi, M. K., Yapanto, L. M., Selvapandian, D., Harish, R., & Subramani, K. (2021). Optical Analysis of the UPQC using PI Controller in Power flow System. IEEE.
Sharma, D. K., Singh, B., Regin, R., Steffi, R., & Chakravarthi, M. K. (2021). Efficient Classification for Neural Machines Interpretations based on Mathematical models. IEEE.
Chakravarthi, M. Kalyan, Watekar, P. R., Babu, A. V., Sateesh, M., & Reddy, P. V. (2012). Optimization of Silica Glass Micro Fiber for Zero Dispersion Wavelength.
Praveen Barmavatu, Mihir Kumar Das, Rathod Subhash, Banoth Sravanthi, Radhamanohar Aepuru, R Venkat reddy, Yalagandala akshay kumar "Designing an Effective Plate Fin Heat Exchanger and Prediction of Thermal Performance Operated Under Different Water Blends Using Machine Learning", Journal of Thermal Sciences and Engineering Applications, ASME Publications, Vol-15/issue-4/pp: 041001-041022, 2023.
Praveen Barmavatu, S A Deshmukh, Mihir Kumar Das, Radhamanohar Aepuru, R Venkat reddy, Banoth Sravanthi “Synthesis and experimental investigation of glass fiber epoxy/saw dust composites for flexural & tensile strength”, Materiale Plastice, vol-59/issue-02/pp:73-81/June 2022.
U.B. Vishwanatha, Y. Dharmendar Reddy, Praveen Barmavatu, B. Shankar Goud “Insights into stretching ratio and velocity slip on MHD rotating flow of Maxwell nanofluid over a stretching sheet: Semi-analytical technique OHAM”, Journal of the Indian Chemical Society, Elsevier Publishers, , Vol-100/issue-3/pp: 100937-10, 2023.
Darapu Kiran Sagar Reddy, Praveen Barmavatu, Mihir Kumar Das, Radhamanohar Aepuru “Mechanical properties evaluation and microstructural analysis study of ceramic-coated IC engine cylinder liner”, Elsevier material today proceedings, Vol-76/Part-3, pp: 518-523, 2023.
Darapu Kiran Sagar Reddy, Praveen Barmavatu, Mihir Kumar Das, Radhamanohar “Aepuru Experimental analysis of coated engine cylinder liners”, AIP Conference Proceedings, ISSN 1551-7616/ Vol 2786/ Paper ID: 030002, 2023.
Sonali Anant Deshmukh, Praveen Barmavatu, Mihir Kumar Das, Bukke Kiran Naik, Radhamanohar Aepuru “Heat Transfer Analysis in Liquid Jet Impingement for Graphene/Water Nano Fluid”, Springer Lecture Notes in Mechanical Engineering (LNME), ICETMIE-2022, pp: 1079–1090.
Barmavatu Praveen, Madan mohan reddy Nune, Yalagandala akshay kumar, Rathod Subhash, “Investigating the Effect of Minimum Quantity Lubrication on Surface Finish of EN 47 Steel Material”, Elsevier material today proceedings, , Vol-38/Part-05, pp-32-53-3257.
Yalagandala akshay kumar, Shaik shafee, Barmavatu Praveen “Experimental investigation of residual stresses in a die casted alluminium fly wheel” Elsevier material today proceedings /vol19/issue-Part-02/pp: A10-A18/October2019, Impact Factor- 2.59.
Barmavatu Praveen & S. chakradhar Goud “fabrication of compact heat exchanger with composite alloys” International journal of innovative technology and exploring engineering, 8(6S4), 717–721.
Barmavatu Praveen, Yalagandala Akshay Kumar, Banoth Sravanthi, H. Ameresh “Methodological Investigation on recycling of Plastic Polymers-A Review” International journal of scientific & technological research 2277-8616/vol-9/issue-03/pp:1537-1542/march 2020.
Barmavatu Praveen & s chakradhar goud “CFD approach for different fluids varients in compact heat exchanger at different parametric conditions” International journal of scientific & technological research, /vol-8/issue-12/pp:2288-2296/december2019. https://www.ijstr.org/paper-references.php?ref=IJSTR-1119-24385
G. Aziz, S. Sarwar, R. Waheed, and M. S. Khan, “The significance of renewable energy, globalization, and agriculture on sustainable economic growth and green environment: Metaphorically, a two-sided blade,” Nat. Resour. Forum, no. April, pp. 1–21, 2023.
N. Elouaer, R. Waheed, S. Sarwar, and G. Aziz, “Does Gender Diversity and Experience Moderate the Impact of Tax Aggressiveness on Corporate Social Responsibility: A Study of UAE Listed Companies,” Sustainability, vol. 14, no. 21, p. 14348, Nov. 2022.
G. Aziz, S. Sarwar, R. Waheed, and M. S. Khan, “Significance of hydrogen energy to control the environmental gasses in light of COP26: A case of European Countries,” Resour. Policy, vol. 80, no. September 2022, p. 103240, 2023.
G. Aziz, R. Waheed, S. Sarwar, and M. S. Khan, “The Significance of Governance Indicators to Achieve Carbon Neutrality: A New Insight of Life Expectancy,” Sustainability, vol. 15, no. 1, pp. 1–20, 2023.
A, V. V. ., T, S. ., S, S. N. ., & Rajest, D. S. S. . (2022). IoT-Based Automated Oxygen Pumping System for Acute Asthma Patients. European Journal of Life Safety and Stability (2660-9630), 19 (7), 8-34.
A. Qadeer, M. Wasim, H. Ghazala, A. Rida, and W. Suleman, “Emerging trends of green hydrogen and sustainable environment in the case of Australia,” Environ. Sci. Pollut. Res., 2023.
A. T. Hoang and V. V. Pham, “A study on a solution to reduce emissions by using hydrogen as an alternative fuel for a diesel engine integrated exhaust gas recirculation,” in International Conference on Emerging Applications in Material Science and Technology: ICEAMST2020, 2020, p. 020035.
A. T. Hoang, V. V Le, A. X. Nguyen, and D. N. Nguyen, “A Study On The Changes In Microstructure And Mechanical Properties Of Multi-Pass Welding Between 316 Stainless Steel And Low-Carbon Steel,” Journal of Advanced Manufacturing Technology (JAMT), vol. 12, no. 2, pp. 25–40, 2018.
D. Cai, G. Aziz, S. Sarwar, M. I. Alsaggaf, and A. Sinha, “Applicability of denoising based artificial intelligence to forecast the environmental externalities,” Geosci. Front., p. 101740, 2023.
G. Aziz and S. Sarwar, “Empirical Evidence of Environmental Technologies , Renewable Energy and Tourism to Minimize the Environmental Damages : Implication of Advanced Panel Analysis,” Int. J. Environ. Res. Public Health, vol. 20, no. 6, p. 5118, 2023.
G. Aziz and S. Sarwar, “Revisit the role of governance indicators to achieve sustainable economic growth of Saudi Arabia–pre and post implementation of 2030 Vision,” Struct. Chang. Econ. Dyn., vol. 66, pp. 213–227, 2023.
G. Aziz, S. Sarwar, K. Nawaz, R. Waheed, and M. S. Khan, “Influence of tech-industry, natural resources, renewable energy and urbanization towards environment footprints: A fresh evidence of Saudi Arabia,” Resour. Policy, vol. 83, p. 103553, Jun. 2023.
G. Aziz, S. Sarwar, M. Shahbaz, M. N. Malik, and R. Waheed, “Empirical relationship between creativity and carbon intensity: a case of OPEC countries,” Environ. Sci. Pollut. Res., vol. 30, no. 13, pp. 38886–38897, Mar. 2023.
G. Aziz, S. Sarwar, M. W. Hussan, and A. Saeed, “The importance of extended-STIRPAT in responding to the environmental footprint: Inclusion of environmental technologies and environmental taxation,” Energy Strateg. Rev., vol. 50, no. May, p. 101216, 2023.
H.A.A. Alsultan , F.H.H. Maziqa and M.R.A. Al-Owaidi "A stratigraphic analysis of the Khasib, Tanuma and Sa’di formations in the Majnoon oil field, southern Iraq," Bulletin of the Geological Society of Malaysia, vol. 73, p.163 – 169, 2022 .
H.A.A. Alsultan , M.L. Hussein, , M.R.A. Al-Owaidi , A.J. Al-Khafaji and M.A. Menshed "Sequence Stratigraphy and Sedimentary Environment of the Shiranish Formation, Duhok region, Northern Iraq", Iraqi Journal of Science, vol.63, no.11, p.4861-4871, 2022.
H.A.A. Alsultan and K. H. Awad "Sequence Stratigraphy of the Fatha Formation in Shaqlawa Area, Northern Iraq," Iraqi Journal of Science ,vol. 54, no.2F, p.13-21, 2021.
I.I. Mohammed, and H. A. A. Alsultan "Facies Analysis and Depositional Environments of the Nahr Umr Formation in Rumaila Oil Field, Southern Iraq," Iraqi Geological Journal, vol.55, no.2A, p.79-92, 2022.
I.I. Mohammed, and H. A. A. Alsultan "Stratigraphy Analysis of the Nahr Umr Formation in Zubair oil field, Southern Iraq," Iraqi Journal of Science, vol. 64, no. 6, p. 2899-2912, 2023.
Jerusha Angelene Christabel G, Shynu T, S. Suman Rajest, R. Regin, & Steffi. R. (2022). The use of Internet of Things (Iot) Technology in the Context of “Smart Gardens” is Becoming Increasingly Popular. International Journal of Biological Engineering and Agriculture, 1(2), 1–13.
L. Lei, G. Aziz, S. Sarwar, R. Waheed, and A. K. Tiwari, “Spillover and portfolio analysis for oil and stock market: A new insight across financial crisis, COVID-19 and Russian-Ukraine war,” Resour. Policy, vol. 85, p. 103645, Aug. 2023.
L. Qin, G. Aziz, M. W. Hussan, A. Qadeer, and S. Sarwar, “Empirical evidence of fintech and green environment: Using the green finance as a mediating variable,” Int. Rev. Econ. Financ., vol. 89, no. PA, pp. 33–49, 2023.
N. Kaur and S. D. Tiwari, “Estimation of magnetic anisotropy constant of magnetic nanoparticles,” in DAE Solid State Physics Symposium 2019, 2020.
N. Kaur and S. D. Tiwari, “Evidence for spin-glass freezing in NiO nanoparticles by critical dynamic scaling,” J. Supercond. Nov. Magn., vol. 34, no. 5, pp. 1545–1549, 2021.
N. Kaur and S. D. Tiwari, “Role of particle size distribution and magnetic anisotropy on magnetization of antiferromagnetic nanoparticles,” J. Phys. Chem. Solids, vol. 123, pp. 279–283, 2018.
N. Kaur and S. D. Tiwari, “Role of wide particle size distribution on magnetization,” Appl. Phys. A Mater. Sci. Process., vol. 126, no. 5, 2020.
N. Kaur and S. D. Tiwari, “Thermal decomposition of ferritin core,” Appl. Phys. A Mater. Sci. Process., vol. 125, no. 11, 2019.
O. Fabela, S. Patil, S. Chintamani, and B. H. Dennis, “Estimation of effective thermal conductivity of porous media utilizing inverse heat transfer analysis on cylindrical configuration,” in Volume 8: Heat Transfer and Thermal Engineering, 2017.
Priscila, S. S., Rajest, S. S., T, S. and G, G. (2022) “An Improvised Virtual Queue Algorithm to Manipulate the Congestion in High-Speed Network”, Central Asian Journal of Medical and Natural Science, 3(6), pp. 343-360.
R. Regin, Steffi. R, Jerusha Angelene Christabel G, Shynu T, S. Suman Rajest (2022), “Internet of Things (IoT) System Using Interrelated Computing Devices in Billing System”, Journal of Advanced Research in Dynamical and Control Systems, Vol.14, no.1, pp. 24-40.
R. Steffi, G. Jerusha Angelene Christabel, T. Shynu, S. Suman Rajest, R. Regin (2022), “ A Method for the Administration of the Work Performed by Employees”, Journal of Advanced Research in Dynamical and Control Systems, Vol.14, no.1, pp. 7-23.
Rajest, S. S. ., Regin, R. ., T, S. ., G, J. A. C. ., & R, S. . (2022). Production of Blockchains as Well as their Implementation. Vital Annex : International Journal of Novel Research in Advanced Sciences, 1(2), 21–44.
Regin, D. R., Rajest, D. S. S., T, S., G, J. A. C., & R, S. (2022). An Automated Conversation System Using Natural Language Processing (NLP) Chatbot in Python. Central Asian Journal Of Medical And Natural Sciences, 3(4), 314-336.
S. Patil, S. Chintamani, B. H. Dennis, and R. Kumar, “Real time prediction of internal temperature of heat generating bodies using neural network,” Therm. Sci. Eng. Prog., vol. 23, no. 100910, p. 100910, 2021.
S. Patil, S. Chintamani, J. Grisham, R. Kumar, and B. H. Dennis, “Inverse determination of temperature distribution in partially cooled heat generating cylinder,” in Volume 8B: Heat Transfer and Thermal Engineering, 2015.
S. S. Rajest, R. Regin, S. T, J. A. C. G, and S. R, “Improving Infrastructure and Transportation Systems Using Internet of Things Based Smart City”, CAJOTAS, vol. 3, no. 9, pp. 125-141, Sep. 2022.
S. Sarwar, G. Aziz, and A. Kumar Tiwari, “Implication of machine learning techniques to forecast the electricity price and carbon emission: Evidence from a hot region,” Geosci. Front., no. xxxx, p. 101647, 2023.
S. Sarwar, G. Aziz, and D. Balsalobre-Lorente, “Forecasting Accuracy of Traditional Regression , Machine Learning , and Deep Learning : A Study of Environmental Emissions in Saudi Arabia,” Sustainability, vol. 15, no. 20, p. 14957, 2023.
S. Sarwar, R. Waheed, G. Aziz, and S. A. Apostu, “The Nexus of Energy, Green Economy, Blue Economy, and Carbon Neutrality Targets,” Energies, vol. 15, no. 18, p. 6767, Sep. 2022.
T, S., Rajest, S. S., Regin, R., Christabel G, J. A., & R, S. (2022). Automation And Control Of Industrial Operations Using Android Mobile Devices Based On The Internet Of Things. Central Asian Journal of Mathematical Theory and Computer Sciences, 3(9), 1-33.
X. D. Pham, A. T. Hoang, and D. N. Nguyen, “A Study on the Effect of the Change of Tempering Temperature on the Microstructure Transformation of Cu-Ni-Sn Alloy,” International Journal of Mechanical & Mechatronics Engineering, vol. 18, no. 04, pp. 27–34, 2018.
Y. Cui, G. Aziz, S. Sarwar, R. Waheed, Z. Mighri, and U. Shahzad, “Reinvestigate the significance of STRIPAT and extended STRIPAT: An inclusion of renewable energy and trade for gulf council countries,” Energy Environ., p. 0958305X231181671, Jun. 2023
Published
2024-03-28
How to Cite
Shagur Banu, M., & B. Vaidianathan. (2024). Maximum Power Point Tracking Dual Axis Solar Panel Using Arduino UNO. Central Asian Journal of Theoretical and Applied Science, 5(2), 49-63. Retrieved from https://cajotas.centralasianstudies.org/index.php/CAJOTAS/article/view/1447
Section
Articles
